Before I took mine apart, I went looking for everything the web knows about the Heathkit SA-2. Here is the summary.
What it is
The SA-2 is a stereo integrated amplifier/preamplifier kit from the Heath Company of Benton Harbor, Michigan. It was advertised as new in January 1960 at a kit price of $52.95. In August 1961 Heathkit replaced it with the AA-151 — described in their own ad as “the popular SA-2 model all dressed up in brand-new styling” — so the SA-2 was made for roughly 1960–1961. Black faceplate with gold trim, 15″ wide × 4¼″ high × 8″ deep, about 23 lbs shipping weight, runs on 117V AC.
The circuit
11 tubes: 2× 12AX7 (magnetic phono preamp, RIAA), 2× 6AU6 (line/driver), 2× 6AN8 (pentode gain stage + triode phase inverter — the stage I am bench-working in this diary), 4× EL84/6BQ5 in push-pull ultralinear (output transformers are Heath part 51-29), and 1× GZ34/5AR4 rectifier. No selenium rectifier anywhere — rectification is by tube.
Controls: 4-position input selector (magnetic phono / crystal phono / tuner / auxiliary), 6-position function switch (Amp A, Amp B, Mono A, Mono B, Stereo, Stereo Reverse), concentric clutched volume, ganged bass and treble, speaker phasing switch, hum balance. Speaker outputs for 4, 8 and 16 ohms. One quirk: all four EL84s share a single cathode bias network in stock form, so a matched quad is needed.
Heathkit’s published specifications (1960 ads)
- Power: 14 W per channel (“hi-fi” rating; 12 W “professional”, 16 W “utility”; 28 W mono)
- Power response: ±1 dB, 20 Hz–20 kHz at 14 W
- THD: under 2%, 30 Hz–15 kHz at 14 W
- IM distortion: under 1% at 16 W
- Hum and noise: 47 dB below 14 W on magnetic phono, 63 dB on tuner/crystal phono
- Phono sensitivity: 3 mV, RIAA equalized
What restorers say today
Standard work on a 60-year-old SA-2: replace the power-supply can electrolytic and the other electrolytics, swap the Pyramid paper coupling capacitors for film, replace drifted carbon-comp resistors, reflow joints, clean the switches and pots. Known weak points: worn treble-pot traces, popping selector/function switches, the RCA jacks mounted under the chassis, broken rear feet, and plain old kit-build variability — every SA-2 was soldered by a hobbyist. Owners also advise running it at about 117V, since modern line voltage pushes the B+ high. A popular modification (Eli Duttman, AudioAsylum) is splitting the shared EL84 bias network into one per channel, so matched pairs are enough instead of a matched quad.
The sound gets consistent praise: crisp but never harsh, with surprisingly big bass for 14 watts, and a quiet, warm phono stage.
Used prices I found (mostly asking prices): about $200 untested/for parts, $350–400 working as-is, and a fully restored one sold on Reverb for $450.
Photos and further reading
- A gallery of 92 SA-2 photos (myvintagetubeamp.com): https://myvintagetubeamp.com/2019/10/12/vintage-heathkit-sa-2-integrated-stereo-tube-amplifier-el-84-phono-see-condition/
- Radiomuseum SA-2 entry: https://www.radiomuseum.org/m/heath_usa_en_6.html
- Factory schematic (Nostalgic Kits Central): https://www.nostalgickitscentral.com/heath/products/audio_stereo.html
- AA-151 manual (same circuit, restyled): https://cdn3.guidespdf.com/view/1308/1308495-aa151.pdf
- diyAudio SA-2 thread: https://www.diyaudio.com/community/threads/heathkit-sa2.213916/
My own SA-2’s photos and bench notes are in the Heathkit SA-2 project page and Diary 1–3.
— Eric